TraVis - Flughafen Graz

Address details

Position

Distance to airport

Height above sea level

Flight table

INFORMATION

Welcome to the weather forecast dialogue!
Our AI with neural network is based on comprehensive weather data, which makes it possible to do a precise analysis of historical operating directions.
Please note that the Sky Cast mode only offers operating direction forecasts.

Help

expand_more

CURRENT mode

In CURRENT mode, you can see flight and noise information from Graz Airport with a time lag of 86400 seconds. The application is automatically opened in CURRENT mode when launched.

expand_more

ARCHIVE mode

In ARCHIVE mode, archived flight and noise information from Graz Airport is displayed. You may select any time within the last 2 months to view information you are interested in. Archived information can be replayed at a higher rate than the current data. Load the date with the calendar button and set the speed in the control box at the top left.

expand_more

Switching between CURRENT und ARCHIVE mode

Clicking on the start button or the calendar button will enable you to switch between both modes.

expand_more

Measuring Points / Measuring Stations / Measurements

The measuring stations are displayed as measuring points. If a measured sound level is below the threshold defined individually for every station, the measuring point will be displayed in green

. If the noise level is above, it will be displayed in dark red

. If the noise level is recognised as an aircraft noise event, the measuring point will turn light red

.
If a measuring station is temporarily out of service or no measurements delivered for technical reasons, the station will be displayed turquoise without any values

. Furthermore, the measuring point will turn turn dark grey

if a noise level of 90 dB(A) is exceeded. This occurs for example when the calibration is checked. If a measuring station is coloured grey

, a downtime is indicated. This can be caused by weather conditions (e.g. thunderstorms, strong gusts of wind, etc.). The downtime of the measuring station will not be taken into account for the continuous noise level calculation or any other reports. By clicking on the measuring station, detailed information will be displayed at the right side of your browser window, such as name of the measuring station, height above sea level, actual noise level, etc.

expand_more

Aircraft Tracks

Landing and departing aircraft can be recognised by their flight track in the system. They length of the flight paths can be adjusted in the View Options. The green coloured flight tracks indicate the path of landing aircraft and the blue tracks that of departing aircraft.

expand_more

Time

In the "CURRENT mode" in TraVis the traffic is displayed with a 86400 seconds time lag for technical reasons. The system time is local time (CET resp. CEST) at Graz Airport.

expand_more

Weather Information

In the header area you see information about the weather situation at the time you have chosen. Move the mouse cursor over this area to open additional weather data! This includes date and time, temperature, humidity, precipitation, wind speed and direction are displayed. Weather information is updated every 30 minutes.

expand_more

Marked Object

Clicking on a particular aircraft or monitoring station will display any relevant detailed information. The appropriate information will be shown on the right side of the screen.

expand_more

Mark your own position

You can mark your own position using the home symbol - just drag the little house icon with the mouse from the header area to the map and move it to your own position. Afterwards you can open the distance graphics for selected flights in the data panel on the right side of your browser window. Additionally you can open a context menu by clicking the right mouse button over the home symbol - in this menu you can open a window with information about the marked position and remove the home marker.

expand_more

Radar Data

For technical reasons there may be a few flights with incorrect track display. This can happen especially for smaller airplanes.

expand_more

Calculated noise level

If you mark your own position (home symbol in "Setup"), you can get information about distance, flight level and a calculated noise level for most aircraft types. The level calculation is based on measured data from the noise monitoring system and the calculation algorithm "Anleitung zur Berechnung von Fluggeräuschen". The calculated level maybe slightly different from real values.

expand_more

Measuring station statistics

You can gain information about acoustic measuring values and configuration data with relevant traffic data for every measuring station. The statistics module presents information about numbers and levels of noise events caused by aircraft flights in diagrams and tables. The values can be related to the number of flights, runway usage, type mix and route usage. You can start the statistics module with the button under the data of the selected measuring station.

expand_more

View options

Under "View options" (open with tool button in the header area) you can customise your view of aircraft movements and flight data. The flight tracks can be switched on and off by using the button "Show flight tracks", the noise monitoring terminals can be switched on and off by using the button "Show NMTs". Information referring to every aircraft movement can be switched on and off by using the button "Show data flags for all flights". Detailed information can be displayed by using the button "Show big data flags".

expand_more

Tips & Tricks

You can also use your keyboard to change the map view. If this area has the input focus, you can zoom out with the - key and zoom into the map using the + key. You can use the arrow keys and PageUp/PageDown keys to change the visible section of the map.

Almost all modern internet browsers include a full page mode, which shows the content of the browser window without the menubar and other toolbars maximized to the full screen. Press the F11 key to start and end this mode.

You can measure distances on the map by right-clicking two (or more) positions on the map. The result of the measurement will be shown in a small information area in the bottom left corner of your browser window. Left-click on the map to stop the measurement.

TraVis - Flughafen Graz

View options

Map

Flights

Layer selection

Address details

Flight table

MY SKY - RESULTS

Language

About TraVis

TraVis - Flughafen Graz

View options

Map

Flights

Layer selection

Address details

Flight table

MY SKY - RESULTS

Language

About TraVis

Share flight